Menu

Wiring diagram for the system with an electronic voltage regulator P/N 12321354758H

The table below shows the radial clearance specifications for all bearings used on the R24 – R69S models

It’s a wide spread misconception that pistons must be round / cylindrical. The opposite is true, This is a new Kolbenschmidt R27 piston 68.50 mm:               From the Internet: Profile: If you roll a piston across a flat surface, you’ll notice it doesn’t roll in a straight line. This characteristic is called profile. Aluminum conducts heat significantly, so pistons are designed with a taper. The top of the piston (near the crown) has a smaller diameter than the bottom (near the skirt). The skirt itself is shaped like a barrel. This taper allows the
Read more »

  Click thumbnail to open the list. R24 – R27           R51/3 – R68           R50 – R69S            

This is specifically aimed at 1 cylinder and /2 gearboxes. If you’ve tried everything and you can’t figure why the gearbox shafts do not turn freely, you can use following very time consuming method  🙂 to determine the cause: Instead of putting all 3 shafts in at the same time, put in 1 shaft at the time. Remove the input shaft seal from the gearbox: the seal makes it harder to rotate the input shaft, making it difficult to assess whether the shaft is running freely. Remove the idler gear and kickstarter gear segment. Whenever you install (and remove) one
Read more »

A “strenght & weakness” overview of the different seal materials available in the market.

Very informative video! https://fb.watch/gQycYmmz_h/    

The oil slinger screws are not available from BMW anymore. Most suppliers now offer a general purpose DIN 963 M6 x 10 screw. However, the head of this screw is higher than that of the original screw: the head of the screw protrudes above the oil slinger surface. This may be undesirable in some cases. We now supply oil slinger screws with the same dimensions as the original screw.

The BMW specification for the radial clearance of the conrod big end & crankpin is based on the use of slightly spherical rollers in some of the crankshafts. The use of spherical rollers prevents the rollers from “biting” when the crankshaft flexes at high RPM. Today the new FAG Dürkopp conrod sets are equipped with cylindrical rollers. This requires a slightly larger radial clearance to prevent the rollers from getting stuck when the crankshaft flexes at high RPM. Spherical rollers (used) are identified by the wear track in the center of the roller:                
Read more »

If the valve adjusting screws have reached their end and there is still insufficient valve clearance, the cause may be (a combination of): the valves sit too deep in the valve seats the cylinder head sleeves have sunk deeper into the cylinder head over time. In our experience, the sleeves at the exhaust side sit usually deeper than at the intake side. Below an example of 2 R27 cylinder heads. The RHS sleeve at the intake side of cylinder head 1 has a height of 88.47 mm The LHS sleeve at the exhaust side of cylinder head 2 has a
Read more »

Staburag is a good alternative for “Prussian Blue” when determining the contact pattern between the crown and pinion gears. By adding a few lines, the contact pattern becomes even easier to read.                  

The drive shaft flange has a press fit with the shaft. A workshop press is needed to press the flange off and onto the shaft. When removing the flange, standard press plates can be used to support the flange. However, to press the flange back on, the drive shaft collar must be supported. There are several ways to do this, but this tool works best for us. The tapered shape of the 2 halves and the ring ensures that the shaft is increasingly clamped during pressing. The edge of the hole between the 2 halves follows the radius of the
Read more »

Valve springs can lose a lot of their strength over the years, as seen with this R25/3 valve spring: a new spring measures 16.6 kg, the old spring 10.1 kg, almost 40% lower. Lower spring tension usually causes no or minor problems on low revving engines, but it can lead to loss of power / misfiring on higher revving engines as a result of valve float                 The test device:  

Recommended press fitting for valve seat inserts in aluminum cylinder heads: OD insert 30 – 40 mm: 0.15 mm / 0.0059″ OD insert 40 – 50 mm: 0.18 mm / 0.0071″   Spindle speed for cutting a seat pocket in aluminum cylinder heads: 400 – 600 rpm It’s recommended NOT to freeze (f.i. with liquid nitrogen) the sintered valve seat inserts before installation. The valve seats are to be pressed in with a flat and square seat driver tool. The valve seat is inserted with the radius side down.   Source: DuraBond

All Matra tools with spindles such as M355, M499 / 1/2, M422a, M501 and M282 work much better (more smoothly) if a small amount of lubricant (eg Molykote G-n Metal Assembly Paste) is applied to the thread. This prevents galling of the thread under heavy load and reduces, to a certain extent, unwanted rotation of the other part of the tool.

The width of rims can be measured in 2 different ways: the inside or the outside. This means that one and the same rim can be indicated both in (for example) 2.15 “and 3.08″ WM2: inside 1.85″ (47 mm) outside 2.72″ (69 mm) WM3: inside 2.15″ (55 mm) outside 3.08” (78.2 mm)      

A frequently asked question is how to fix a leakage of the idle mixing screw. Further tightening the nut of the idle mix screw is certainly not the solution: holes have been drilled in the idle mix screw which connects the idle mix chamber to the the outside air. If fuel leaks out through the same bore, it simply means that the fuel level in the float bowl is too high. (assuming that the bike is on the center stand, if the motorcycle is placed on the side stand, there is a greater risk of leakage) If the carbs keep leaking, it’s
Read more »

By Michel Loos, The Netherlands The photos are self-explanatory. Steps:  filing  – sanding – pneumatic hammer – aluminum oxide blasting (Edelkorund) – glass bead blasting  

Cylinder black with part nr. 09122 For temperatures up to 500 °C continuous use and up to 700 °C with impact load 200 ml is sufficient for 2 to 3 large cylinders. Ideal for spraying and painting engine cylinders, exhaust systems and other metal objects subject to high heat. Classic cylinder lacquer is initially thermoplastic; in other words although it is air-drying, it becomes sticky even with moderate heat, expands and hardens again when it cools down. This process is repeated as long as the polymerization temperature is not reached. The lacquer must be heated at least once to 150-180 °C to finally cure. After
Read more »

BING jets are stamped with numbers, such as 35, 40 (idle jets) and 110, 115, 120 etc (main jets). One would expect that these numbers refer to the diameter of the jet bore, however this is not the case. This is confimed by the company BING in Germany. A few examples of main jets measured with a wire / jet gauge: BING 44-051 main jet 130 = gauge 120 (= 1.2 mm) main jet 125 = gauge 110 (= 1.1 mm) main jet 120 = gauge 105 (= 1.05 mm) main jet 110 = gauge 95 (=0.95 mm)            
Read more »

With hardly any new carburetors being produced by BING for the < 1969 BMW mono and twin motorcycles, it’s getting increasingly important to be able to repair and recondition the used original carburetors. Luckily, special parts and tools are available nowadays to restore the carburetors to a good working condition. A. Idle mix screw: very often, the M7 x 0.75 mm screw thread in the carburetor housing is worn out. There are 2 good solutions to this problem. 1. drill the threaded hole to 7.2 mm – cut M8 x 0.75 mm screw thread – install the idle mix screw with
Read more »

electronic-voltage-regulator-bmw-r24-r26-eng electronic-valtage-regulator-bmw-r51-3-r69s-eng electronic-voltage-regulator-bmw-r27-r50-eng

By MS Motor Service (Kolbenschmidt) Click here to open as PDF: KS Installation of piston rings

Source: Wikipedia https://www.batterystuff.com/kb/ The Lead Acid battery is made up of plates, lead, and lead oxide (various other elements are used to change density, hardness, porosity, etc.) with a 35% sulfuric acid and 65% water solution. This solution is called electrolyte, which causes a chemical reaction that produce electrons. When you test a battery with a hydrometer, you are measuring the amount of sulfuric acid in the electrolyte. If your reading is low, that means the chemistry that makes electrons is lacking. So where did the sulfur go? It is resting on the battery plates and when you recharge the
Read more »

Overview of carburetor nr’s and settings  

A visual inspection of the spark plugs can serve as a good indicator of the condition and tuning of the engine. This Bosch sheet may help to identify the possible cause in case of trouble. (click to enlarge)

Guidelines for correct installation of (Bosch) spark plugs