Menu

The correct functioning of a capacitor can be measured with (for example) a FLUKE multimeter. The value specified by the manufacturer is 0.22 μF (microfarad). Over time, a capacitor’s performance can be expected to decline. The left photo shows a broken capacitor: the measured value is 0.131 nF (nanofarad) = 0.000131 μF The right photo shows a properly functioning capacitor: the measured value is 0.249 μF. This is 13% higher than the specified value, but this does not affect proper operation. The value specified by the manufacturer is a chosen ideal value for the expected average engine rpm. This value is therefore
Read more »

It’s a wide spread misconception that pistons must be round / cylindrical. The opposite is true, This is a new Kolbenschmidt R27 piston 68.50 mm:               From the Internet: Profile: If you roll a piston across a flat surface, you’ll notice it doesn’t roll in a straight line. This characteristic is called profile. Aluminum conducts heat significantly, so pistons are designed with a taper. The top of the piston (near the crown) has a smaller diameter than the bottom (near the skirt). The skirt itself is shaped like a barrel. This taper allows the
Read more »

The only difference between the Denfeld en Pagusa saddle is the saddle deck. There are small differences between the saddle deck frames: the shape of the frame and the front threaded bolt. The Pagusa saddle bolt it is a bit longer and has a spacer so that the front of the saddle deck sits +- 1.5 cm higher compared to the Denfeld saddle deck. The grain texture of the Denfeld rubber saddle deck surface is finer than the Pagusa grain texture. There is no quality difference All other parts are the same: subframe, Z-bracket, rubber spring, spring stop piece, mounting
Read more »

Comparison of the different gearbox cam plates used in the R24 – R27 and R50 – R69S models. For more information about the R50 – R69S shifting system, click following links: Smooth shifting R50 – R69S R50 – R69S Old and New style shifter mechanism  

A “strenght & weakness” overview of the different seal materials available in the market.

The oil slinger screws are not available from BMW anymore. Most suppliers now offer a general purpose DIN 963 M6 x 10 screw. However, the head of this screw is higher than that of the original screw: the head of the screw protrudes above the oil slinger surface. This may be undesirable in some cases. We now supply oil slinger screws with the same dimensions as the original screw.

Without direct comparison, it can be difficult to distinguish the difference between the R25-R25/2, R26 and R27 exhaust pipes. This photo shows how you can easily determine the type of exhaust pipe:   The R25, R25/2 exhaust pipe is significantly longer at the straight end than the R26 exhaust pipe:

The width of rims can be measured in 2 different ways: the inside or the outside. This means that one and the same rim can be indicated both in (for example) 2.15 “and 3.08″ WM2: inside 1.85″ (47 mm) outside 2.72″ (69 mm) WM3: inside 2.15″ (55 mm) outside 3.08” (78.2 mm)      

There are 2 versions available in the market. The one on the right has a lower push button housing. The hole in the housing does not align with the hole in the connector, as a result the wire cannot be connected properly.

BING jets are stamped with numbers, such as 35, 40 (idle jets) and 110, 115, 120 etc (main jets). One would expect that these numbers refer to the diameter of the jet bore, however this is not the case. This is confimed by the company BING in Germany. A few examples of main jets measured with a wire / jet gauge: BING 44-051 main jet 130 = gauge 120 (= 1.2 mm) main jet 125 = gauge 110 (= 1.1 mm) main jet 120 = gauge 105 (= 1.05 mm) main jet 110 = gauge 95 (=0.95 mm)            
Read more »

Different exhaust pipes are available in the market, unfortunately not always an exact replica of the original pipes: the shape of the bends does not correspond with the original BMW exhaust pipes as can be seen on this picture. The 2 lower exhaust pipes are identical to the original pipes.   Next to that, these pipes follow a slightly different path than the original exhaust pipes. This causes a problem for the R67 – R67/3 models: in the horizontal section, they’re not running close enough to the frame, causing too little clearance between the brake pedal and the right-hand exhaust pipe,
Read more »

With hardly any new carburetors being produced by BING for the < 1969 BMW mono and twin motorcycles, it’s getting increasingly important to be able to repair and recondition the used original carburetors. Luckily, special parts and tools are available nowadays to restore the carburetors to a good working condition. A. Idle mix screw: very often, the M7 x 0.75 mm screw thread in the carburetor housing is worn out. There are 2 good solutions to this problem. 1. drill the threaded hole to 7.2 mm – cut M8 x 0.75 mm screw thread – install the idle mix screw with
Read more »