Products
- Hex bolt M6 x 10 - SSt
- Lock screw for toolbox lid (>1952) - SSt polished
- Washer set for lock screw for toolbox lid (>1952)
- Countersunk screw M4 x 20 for toolbox lock
- Air filter insert LX193 (for Knecht LP492 air filter)
- Relay for blinker 6V Wehrle, 31 = (-), 49 = (+), 49A = switch
- Lock screw for toolbox lid, complete (>1952) - SSt polished
- Ignition coil - high quality, made in Germany ►see details
- Relay for blinker 6V 2 x 21W electronic
- Relay for blinker 6V 2 x 21W, X = (+), L = switch
- Tank badge R25/3 - R69S
- Tank badge R24 - R25/2
- Bushing speedometer cable in gearbox - SSt
- Hardy disk, urethane 17 mm ►see details
- Clamping screw M4.5 for original ignition coil
- Gasket for neutral light fixture
- Ball bearing FAG 6207 C3 crankshaft rear R26, R27 & ring gear R51/2 - R68
- Ball bearing FAG 6207 M - C3 for crankshaft - brass cage ►see details
- Rear brake rod clevis, M6 - SSt (available for pre-order)
- Handlebar - high model LN5 Fehling ►see details
- Handlebar - mid high model LN4 ►see details
- Cylinder stud bolt M10 x 25 (+3 mm) - SSt
- Stud for generator front cover M6 / M6 - SSt
- Knee pad (right side) for Schorsch Meier fuel tank R51/3 ►see details
- Knee pad (left side) for Schorsch Meier fuel tank R51/3 ►see details
- Hex nut M8 x 1, flat, SW13 - zinc plated
- Bearing 6204 for wheel hub + 0.02 mm outside diameter (available for pre-order)
- Bearing 6204 for wheel hub + 0.04 mm outside diameter (available for pre-order)
- Bearing 6204 for wheel hub + 0.06 mm outside diameter (available for pre-order)
- Bearing 6204 for wheel hub + 0.08 mm outside diameter (available for pre-order)
- Bearing 6204 for wheel hub + 0.10 mm outside diameter (available for pre-order)
- Bearing 6204 for wheel hub + 0.12 mm outside diameter (available for pre-order)
- Bearing 6204 for wheel hub + 0.16 mm outside diameter (available for pre-order)
- Bearing 6204 for wheel hub + 0.20 mm outside diameter (available for pre-order)
- Shim 1.5 mm, for 30° gear set (17 mm taper)
- Spring washer, drive shaft - gear box
- Cam with chain for throttle
- Covering, lower, polished alu., after-market
- Camshaft R27 Sports version 328° (available for pre-order)
- Used part: throttle housing R26, R27 (price & availability on request)
- Fuel cock M14 x 1.5 with filter
- Stop spring, inner - centrifugal governor (old)
- Spring holder R51/2
- Used part: axle holder (price & availability on request)
- Used part: axle holder, slotted (price & availability on request)
- Coupling nut (lower) for "Everbest" fuel cock - SSt
- Mechanical voltage regulator 6V DC (Z-Regler) - NOS
- Mechanical voltage regulator 6V
- Capacitor 12V (NOS)
- Capacitor 12V, 180W AC (available for pre-order)
