Products
- Used part: carburetor slide cover plate, LH side, Bing 20-351
- Hub cap, aluminum (unfinished, not polished) R51/3 - R68 ►see details
- Speedometer cable R12 - R17, R5 - R71, R51/2, L = 100 cm OEM product
- Clutch Pressure plate guide pin
- Flange on driveshaft R24
- Flange on driveshaft R5 - R71, R51 - R51/2
- Raised countersunk screw M6 x 18 - SSt
- Bush bearing for kick starter shaft
- Lens head countersunk screw M5 x 22, Kickstarter - SSt
- Bolt Ø 14 mm for brake rod & brake lever
- Bolt Ø 14 mm for brake rod & brake lever - polished SSt
- Die M8 x 1 HSS - metrical fine - Dormer
- Gasket ring for carburetor R26, R27 Bing 165-135
- Retainer for rear drive hub Matra 331650 (R50/5 - R100RS)
- Valve cover gasket R2, R20, R23
- Cylinder head gasket R2, R20, R23
- Flat washer Ø 10.5 mm - SSt
- Spring cover, upper, Ø 66 mm R25 - polished aluminum
- Lens for Hella blinker, after-market (with E-mark)
- Wet air filter R5- R71
- Hex bolt M8 x 25 for headlamp - SSt
- Hex bolt M8 x 25 for headlamp - polished SSt
- Washer for headlight
- Hex nut M8 x 1 SW14 - untreated
- Wheel hub bushing with built-in bearings and gaskets ►see details
- Tapered roller bearing set for steering head (2 pcs)
- BMW R50 - R69US Motorcycle Restoration and Service Manual
- Set of connecting rod, tapered crankpin, roller cage & rollers (available for pre-order)
- Crankcase vent tube, straight cut, polished SSt
- Valve spring
- Plate spring for horn (3 pcs) - SSt
- Pilot ring (Repassierring) Matra 5048 for R50S, R68 - R69S - Alu
- Crash bar for Hella tail light
- Set of connecting rod, crankpin (Ø 36 x 54.5), roller cage & rollers (available for pre-order)
- Set of connecting rod,cylindrical crankpin (Ø 36 x 53), roller cage & rollers (avaible for pre-order)
- Clutch plate - oil resistant - Siebenrock ►see details
- Carburetor: boring carburetor tube for oversized slide R25/3 - R60/2
- Carburetor: boring carburetor tube for oversized slide R25, R25/2, R51/2 - R67/3
- Service: carburetor - boring carburetor tube for oversized slide R26, R27
- O-ring for idle jet and mixture screw (Bing 65-704)
- Cable from turn signal switch to headlamp (4 wires) ►see details
- Cable from turn signal switch to headlamp + 8 cm (4 wires) ►see details
- Cap for steering lock, with pin and corrugated washer
- Service: cylinderhead - overhaul of cylinderhead R24 - R90S ►see details
- Service: cylinder - boring and honing
- Gasket ring Bing 65-710
- Insert Bing 25-016-5/1 (Nr. 5/1) - after market
- Set: Idle mix screw, cap, sleeve and jam nut
- Felt ring for gearbox output flange 36 x 47 x 5 mm
- Clutch compression ring
