Products
- Crankshaft roller bearing FAG 6004 in distribution cover, - 0.02 mm inner race ►see details
- Double angular contact bearing SKF 3303 ATN9 - PA cage
- Hex Bolt M6 x 25 - SSt (alternative to grub screw)
- Cable duct in rear fender R50 - R69S (N.L.A.)
- Clutch pushrod R51/3 - R68 with R50 clutch and flywheel (tapered end)
- Tapered roller bearing Timken 30203
- Bearing FAG 6302 C3 input shaft rear
- Screw M6 x 16 for handle units (R50/5 - R90S)
- Carburetor slide Ø 24.5 mm for Bing 1/22/5 and /6
- Steib front emblem S350, S500
- Matra 467
- Used part: brake spanner R25, R25/2
- Gasket rope Viton R5, R51, R66
- NOS brake spanner R25, R25/2
- Terminal board on generator R24 - R26 (Pertinax)
- Service: crankshaft - truing of 2 cylinder crankshaft
- Horn 12V, black Ø 100 mm
- Spacer bushing
- Washer Ø 38 for selector lever
- Spacer ring (inside) for selector lever
- Used part: brake shoe front / rear R25, R25/2
- Spring for mirror R45 - R100RT
- Pin for clutch lever 11 x 25 x 21 mm, R5 - R51/2 - SSt
- Cover for seal - kickstarter shaft, R5 - R51/2
- Drive flange output shaft - with key way - seal surface Ø 37 mm, R5 - R71, R51 - R51/2
- Drift bushing for seal output shaft R51/3 - R68
- Fuel cock M14 x 1.5 with filter - R24
- Used Part: cylinder head R27 ►see details
- Rubber strap for battery L = 185 mm - with BMW logo
- Relay (electronic) for blinker 12V, 2 x 21W
- Cam plate NOS, R24 - R25/2 (w/o neutral switch)
- Thrust spring for carbon brush - R51/2
- Cable adjusting screw & nut on carburetor, 25 mm (Bing 50-050)
- Screw for steering damper resistance plate - solo R51 - R71, R51/2
- Tappet guide bushing L = 47.8 mm (reaming required after installation)
- Brace for front fender 18" R26 - R69S - chrome (32.5 cm) ►see details !!
- Used part: oil catchment plate
- Round exhaust nut - polished SSt - M45 x 2 - extra length +3 mm ►see details!!
- Bearing cover, swing arm - Steib LS 200 / S 350 / S 500, polished SSt
- Sleeve for cylinder head bolt R25/2 (R24, R25, R51/2) Ø18.10 (available for pre-order)
- Sleeve for cylinder head bolt R25/2 (R24, R25, R51/2) Ø19.00 (available for pre-order)
- Sleeve for cylinder head bolt R25/2 (R24, R25, R51/2) Ø19.05 (available for pre-order)
- Sleeve for cylinder head bolt R25/2 (R24, R25, R51/2) Ø19.10 (available for pre-order)
- Sleeve for cylinder head bolt R25/2 (R24, R25, R51/2) Ø19.10 (available for pre-order)
- Thrust sleeve 10 mm, left side - SSt
- Speedometer cable R12 - R17, R5 - R71, R51/2, L = 105.5 cm - after market
- Used part: gearbox housing R50 - R69S
- Set screw M6 x 1 x 6 - Allen head
- Service: reporting - phase 1 reporting gearbox (disassembly-cleaning-techn. assesment)
- Stud bolt M6 x 25 - zinc plated steel
