Products
- Cam follower R5 - R51 Ø11 mm (no std. stock item)
- Valve seat ring intake 36.64 x 28.57 x 7.95 mm Kolbenschmidt (needs to be machined)
- Middle brace for front fender R25, R25/2 (unpainted)
- Washer for brake spanner rear - full hub - T = 2.5 mm
- Used part: final drive R25, R25/2 with solo gears 27:6 (price & availability on request)
- Bearing FAG 6204-C-2HRS (CLOSED) for wheel hub
- Tension spring for side stand - SSt (for stainless steel sidestand) ►see details
- Roller for conrod Ø 5.047 x 10 mm ±2μ
- Throttle cable R50/5 - R60/7, 1007 mm (carb with slide) - low handlebar
- Cylinder base gasket - aluminum 1.0 mm R24 - R27
- Cylinder base gasket - aluminum 1.5 mm R24 - R27
- Anti vibration rubber pad between fender and brace ►see details
- Used part: brake lever, rear wheel
- Used part: brake lever, rear wheel
- Valve seat ring intake 42.98 x 33.33 x 7.95 mm DuraBond Snyder (needs to be machined)
- Shim for ring gear - housing cover 0.38 mm
- Shim (secondary) for ring gear in final drive 0.30 x 35 x 45 mm
- Stud M6 x 0.85 / 1.0 x 25 SSt - R5, R51, R66
- Clutch thrust piece R51/3 - R68 +0.04 mm
- Shim 0.10 mm for pinion under angular contact ball bearing
- Spacer ring between bush and bearing, pinion R25 - R27
- Spacer bushing inside - pinion L = 20.2 mm, R25 - R25/3 from nr. 245605
- Shim 0.23 mm for pinion under angular contact ball bearing
- Cylinder head screw M3.5 x 5 mm
- Vehicle identification plate R51/3 - flat
- Washer for aluminum rivet for felt spring R24 - R26
- Aluminum rivet for felt spring R24 - R26 (shaft = 2.5 X 4 mm)
- Spacer tube 168,0 for center stand R20, R23, R24, R35 - SSt
- Spacer tube 27.5 mm for center stand R20, R23, R24, R35 - SSt
- Fibre seal ring A30 x 36 chain cover R5, R51, R51/2
- Used part: ring gear - pinion set 27:6 - R25, R25/2 solo (price & availability on request)
- Used part: ring gear - pinion set 25:6 - R25/3 solo
- Tail light Hella, complete, after-market ►see details
- Rear main bearing holder, L=32.0 mm + 0.30 mm oversize outside ►see details (available for pre-order)
- Float 11 gram, plastic - after market - E10 proof
- Customs clearance costs - inbound
- M8 x 0.75 tap Dormer 6H DIN374 (blind holes) ►see details
- Bush bearing R25
- Speedometer drive in gearbox R5 - R71, R51/2
- Choke lever
- Cable adjuster
- Hylomar jointing compound
- Kukko 21-2 Internal Puller 14 to 19 mm
- Kukko 22-1 Counter-Support
- Kukko 21-V-080 Extender
- Spring plate, clutch R26, R27
- Spring plate, clutch R25/3
- Hex bolt M8 x 35 - polished SSt
- Thrust sleeve 10 mm, left side
- Cap nut M8 SW13
