Products
- Valve cover nut M8 - SSt ►see details
- Stud bolt M8 x 25 - zinc plated ►see details
- Oil pan aluminum ~2 ltr.
- Ignition key - ivory
- Cap nut M10 x 1.5 - SW17- SSt
- Camshaft sprocket RHS - R51/2 (available for pre-order)
- Camshaft sprocket LHS - R51/2 (available for pre-order)
- Hex nut with shoulder black, M10 x 1, SW17
- Complete set of gaskets and seals for R50, R60 engine ►see details
- Service: cylinder head - ultrasonic cleaning
- Service: cylinder head assesment, reporting & handling R24 - R69S
- Collar hex nut M9 x 1 - SW15 - cadmium plated
- Collar hex nut M10 x 1 - SW17 - black
- Valve cover gasket
- Throttle cable, solo / low handlebar R50 - R69S & high handlebar R26 - after market ►see details
- Used part: throttle housing cover
- Fillister head screw for brake light switch M4 x 15 - SSt
- Ball bearing 6403 C3 FAG - R50/5 - R100RS (available for pre-order)
- Pin set Ø 3 and 4 mm, for pin spanner Matra 517 (set of 4 pcs) R51/2 - R68 original cover ►see details
- Used part: drive gear (driveshaft) 13T
- Telescopic leg eye, left, after-market
- Telescopic leg eye, right , after-market
- Service: cylinderhead - renewal of valve guide
- Rubber grommet for headlamp (produced to original techn. drawing)
- Hose clamp 11 - 13 mm for fuel line B7 x 12 - zinc plated
- Alu-bronze threaded bushing M7 / M6 x 0.75 for needle jet and slide stop screw ►see details
- Service: crankshaft - disassembly 1-cylinder crankshaft
- Center stand tension spring R51 - R71, R75, R51/2
- Spring for center stand - polished SSt
- Kickstarter shaft - new (available for pre-order)
- Cap for steering lock - NEIMAN
- Plunjer shaft rear suspension - hard chrome plated & ground <09/1951 (available for pre-order)
- Used part: cylinderhead R26
- Fuse 16 Amp.
- Bearing bushing for crankcase R27 ►see details
- Service: crankshaft - disassembly 2-cylinder crankshaft
- Bolt M6 x 20 SW9 for wheel hub cap - SSt
- Used part: tooth segment - shifter system (availability on request)
- Hex bolt M10 x 1 x 30 for center stand - zinc plated - 10.9
- Roller for conrod Ø 5.016 x 10 mm ±2μ
- Roller for conrod Ø 5.027 x 10 mm ±2μ
- Service: crankshaft - assessment: measuring and reporting (w/o disassembly)
- Bearing bolt for center stand R5 - R71, R51/2 - SSt
- Crankpin 32 x 54.5 mm - cylindrical - for reinforced center web (available for pre-order)
- Ring for Hardy disk - chrome plated
- Ignition key, Hella model, after-market
- Clutch pushrod R50 - R69S (L = 203 mm / 183.2 mm) ►see details
- Shim 0.18 mm for pinion under angular contact ball bearing
- Ferodo brake pads 56 x 55 x 9 mm FDB108P
- Service: crankshaft - hard chroming and precision grinding of front main & nose bearing journal
