Products
- Suspension spring Ø 6.8 mm - after market ►see details
- Used part: brake lever upper "Duplex"
- Driving dog final drive - after market, made in DE ►see details
- Valve guide lock ring (for 13 mm guide) - wide version
- Ground wire connection plate for adapter - Noris
- Brake drum R50 - R69S - OD = 206.0 mm
- Brake drum R50 - R69S - OD = 206.5 mm (available for pre-order)
- Brake drum R50 - R69S - OD = 207.0 mm (available for pre-order)
- Cylinder stud bolt M10 x 25 (+3 mm) - Steel
- Spark plug NGK B7HS short reach (equiv. to Bosch W260T1 / W3AC)
- Toolbox lid for fuel tank R25/3
- Center brace for front fender R25/3
- Lower brace set for front fender R25/3
- Serrated washer J10.5 - Zinc plated
- Gasket & seal set for final drive R25 - R25/3 (R25 from VIN 227550) ►see details
- Service: crankcase - installation of bearing holder in crankcase R27 ►see details
- Ball bearing ring gear FAG 16013
- Bushing 18.9 x 12.9 x 9 mm, for center stand, hardened (oversized ID & OD) ►see details
- Valve cover nut M8 - SSt ►see details
- Stud bolt M8 x 25 - zinc plated ►see details
- Oil pan aluminum ~2 ltr.
- Ignition key - ivory
- Cap nut M10 x 1.5 - SW17- SSt
- Camshaft sprocket RHS - R51/2 (available for pre-order)
- Camshaft sprocket LHS - R51/2 (available for pre-order)
- Hex nut with shoulder black, M10 x 1, SW17
- Complete set of gaskets and seals for R50, R60 engine ►see details
- Service: cylinder head - ultrasonic cleaning
- Service: cylinder head assesment, reporting & handling R24 - R69S
- Collar hex nut M9 x 1 - SW15 - cadmium plated
- Collar hex nut M10 x 1 - SW17 - black
- Valve cover gasket
- Throttle cable, solo / low handlebar R50 - R69S & high handlebar R26 - after market ►see details
- Used part: throttle housing cover
- Fillister head screw for brake light switch M4 x 15 - SSt
- Ball bearing 6403 C3 FAG - R50/5 - R100RS (available for pre-order)
- Pin set Ø 3 and 4 mm, for pin spanner Matra 517 (set of 4 pcs) R51/2 - R68 original cover ►see details
- Used part: drive gear (driveshaft) 13T
- Telescopic leg eye, left, after-market
- Telescopic leg eye, right , after-market
- Service: cylinderhead - renewal of valve guide
- Rubber grommet for headlamp (produced to original techn. drawing)
- Hose clamp 11 - 13 mm for fuel line B7 x 12 - zinc plated
- Alu-bronze threaded bushing M7 / M6 x 0.75 for needle jet and slide stop screw ►see details
- Service: crankshaft - disassembly 1-cylinder crankshaft
- Center stand tension spring R51 - R71, R75, R51/2
- Spring for center stand - polished SSt
- Kickstarter shaft - new (available for pre-order)
- Cap for steering lock - NEIMAN
- Plunjer shaft rear suspension - hard chrome plated & ground <09/1951 (available for pre-order)
